2003-2004 Marauder bulb sizes

[fastblackmerc]

Interior and Exterior bulb sizes

Headlight – 9007 (2)
Fog Light – H1 (2)
Rear Stop Light / Turn Signal – 3157 (4)
High Mounted Stop Light – 912 (2)
Front Map Light – 168 (194) (2)
Rear Light (long overhead console) - 42mm Festoon (1)
Glove Compartment – 168 (194) (1)
License Plate – 168 (194)
Trunk Light – 2122 Festoon
Underhood Light – 906 (2)
Parking Light - 3157NA (amber) (2)
Vanity Mirror – 29, 30 or 31mm 6641 (4)
Rear Reading Light – 45mm Festoon (2)
Front Foot Well – 168 (194) (2)
Reverse - 3156 (2)


NOTE: You can substitute a 194 bulb for a 912, 168 or 906 bulb.

[RF Overlord]

Adding Cornering lamp - 3156 (qty 2)

[the fat bastid]

volt gauge - 168
oil gauge - 168

Not that it matters but since some may want that pedantic stock feeling :D, :
my map lights were 906s
dome light was - 578 (which is the same as the 212-2 festoons)
rear readings - 211-2 (but my trunk was a 212-2)

[2,4shofast]

Don't forget...
Dash Gauge cluster - Six 194 bulbs
Shifter - One 194 bulb

[the fat bastid]

for the dash, i made this:
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 733&stc=1&d=1476309089

so not only 6 illumination but if you are crazy, 10 more for the signals.
the little blue ones ctrlraven thinks are t5s.
I haven't pulled it apart yet.

[Ambitious1]

for the dash, i made this:
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 733&stc=1&d=1476309089

so not only 6 illumination but if you are crazy, 10 more for the signals.
the little blue ones ctrlraven thinks are t5s.
I haven't pulled it apart yet.

This is terrific! I have been looking for something like this for a while!

[JBeezy]

Good info

Sent from my SAMSUNG-SM-G935A using Tapatalk

[2,4shofast]

for the dash, i made this:
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 733&stc=1&d=1476309089

so not only 6 illumination but if you are crazy, 10 more for the signals.
the little blue ones ctrlraven thinks are t5s.
I haven't pulled it apart yet.

That is awesome! Good work, I never swapped my signal lights.:beer:

[ctrlraven]

Headlight Switch - T4 Tall (if replacing with an LED bulb)
Shifter - 168/194

[Turbov6Bryan]

What is the part number for the upgraded LED bulbs inside the digital HVAC head unit?

[fastblackmerc]

What is the part number for the upgraded LED bulbs inside the digital HVAC head unit?

There are no "replaceable" bulbs as they are soldered in.

I solder individual LEDs in place of the incandescent "wheat" bulbs for the buttons and I install an LED for the fan control wheel.

[Turbov6Bryan]

There is no "replaceable" bulbs as they are soldered in.

I solder individual LEDs in place of the incandescent "wheat" bulbs for the buttons and I install an LED for the fan control wheel.

The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

They look like T5 bulbs that you can take out from the back side.

I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

Thank you

[fastblackmerc]

The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

They look like T5 bulbs that you can take out from the back side.

I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

Thank you

Every single one (probably well over 100) I've done has had soldered bulbs.

I can do either green or white LED's.

[fastblackmerc]

The older digital board bulbs are soldered in place nearest the faceplate side, but I have 2 newer with removable bulbs in the face plate.

They look like T5 bulbs that you can take out from the back side.

I did not know there are 2 designs until last night. When you put LED bulbs in these are you doing white or green? I want to do 3 of my marauders this weekend.

Thank you

It would be interesting to see what the Ford P/N is on your EATC's.

To my knowledge if your EATC bulbs are like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20bulbs%20old%20st yle_zpsqt63qauz.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20bulbs%20old%20st yle_zpsqt63qauz.jpg.html)

And the solenoids are like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20old% 20style_zpsz8u3flkc.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20old% 20style_zpsz8u3flkc.jpg.html)

Then you have an older EATC or an F150 EATC (yes they are the same and it's a BI**H to replace the o-rings but it can be done).

If the bulbs are soldered in and the solenoids look like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20new% 20style_zpskpgqvfik.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20new% 20style_zpskpgqvfik.jpg.html)

Then you have a newer unit.

In any case, I can repair them all.

[Turbov6Bryan]

Ok cool. So in your opinion, which LED looks better? White or green?

Ok, just opened both. Mm has solder lights, the one I repaired last night has removable light bulbs????? LOL. It's was in a 98 GM but the head unit is a 2005??

Thoughts?

[Turbov6Bryan]

Yes the older valve pack looks much tougher to repair... I went to the yard
And pulled 3 2002 and older... I am going to return the older ones with the hard to repair valve packs, unless you want them for any reason


Here is the board part# with removable bulbs

[Turbov6Bryan]

Side decal

[the fat bastid]

like 90% sure the third brake light is two 906s. Definitely 194/168 compatible, just the bulbs are unmarked/worn off. Also, I didn't realize it but both of those bulbs were no good.
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 817&stc=1&d=1477245933
what a sexy thumb

[fastblackmerc]

like 90% sure the third brake light is two 906s. Definitely 194/168 compatible, just the bulbs are unmarked/worn off. Also, I didn't realize it but both of those bulbs were no good.
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 817&stc=1&d=1477245933
what a sexy thumb

I replace them with LED strips.

[the fat bastid]

The sun visor bulbs are marked as 14V0.1A-CML. 4 total.
I took some measurements since that seems to be more of a rating than model number (?). 29mm long festoon. the caps being 9mm long each.
Check your lens, Looks like one of mine has a burn mark or something but no burn outs and all the bulbs are working, not sure what caused it.
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 819&stc=1&d=1477330926

[RF Overlord]

that seems to be more of a rating than model number (?)Correct. 14 Volts at 0.1 Amps (100 milliAmps)

Does it look like this (http://www.zasales.biz/14Vo1ACml.html)?

[fastblackmerc]

The sun visor bulbs are marked as 14V0.1A-CML. 4 total.
I took some measurements since that seems to be more of a rating than model number (?). 29mm long festoon. the caps being 9mm long each.
Looks like the 3022 is a compatible size..I think.
Check your lens, Looks like one of mine has a burn mark or something but no burn outs and all the bulbs are working, not sure what caused it.
http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 819&stc=1&d=1477330926

The burn is common for incandescent bulbs.

Rule of thumb....

Incandescent = 15% of energy use is light, 85% is heat

LED = 85% of energy used is light 15% is heat.

BTW. I have some sweet LEDs for the mirrors.

[the fat bastid]

Everyone keeps giving me the wrong equivalent model number for the 14V0.1A-CML . I got 4 Sylvania ZEVO Led DE3175 which is also 12818 3021 3022 3175 6428 6430 equivalent. Was told they would fit since it is 3022. Nope. All light people seem to reference that same wrong light list (the ashtray light one). The metal end caps are too fat to fit in the snaps and it hits the lens from being too fat.

http://www.mercurymarauder.net/forums/attachment.php?attachmentid=44 877&stc=1&d=1478541439

This bulb is called 6641f, among other things.

[DrZ]

This is terrific! I have been looking for something like this for a while!

Excellent! :D

[Maraudernoob92]

It would be interesting to see what the Ford P/N is on your EATC's.

To my knowledge if your EATC bulbs are like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20bulbs%20old%20st yle_zpsqt63qauz.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20bulbs%20old%20st yle_zpsqt63qauz.jpg.html)

And the solenoids are like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20old% 20style_zpsz8u3flkc.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20old% 20style_zpsz8u3flkc.jpg.html)

Then you have an older EATC or an F150 EATC (yes they are the same and it's a BI**H to replace the o-rings but it can be done).

If the bulbs are soldered in and the solenoids look like this:
http://i167.photobucket.com/albums/u133/fastblackmerc/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20new% 20style_zpskpgqvfik.jpg (http://s167.photobucket.com/user/fastblackmerc/media/MM%20Mods/EATC%20Repair/Ford%20EATC%20solenoids%20new% 20style_zpskpgqvfik.jpg.html)

Then you have a newer unit.

In any case, I can repair them all.Hey do you have pics of leds installed ib the eac and how much do you charge

Sent from my SM-G970U using Tapatalk

[fastblackmerc]

Hey do you have pics of leds installed ib the eac and how much do you charge

Sent from my SM-G970U using Tapatalk

It's not just the bulbs. You need to install other "parts".

I charge $45.00 to replace the bulbs for the button & fan wheel lights with LEDs and replace the o-rings.

[NXSBOB]

https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/

Vehicle or Part (https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/#vehicleOrPartPanel)


2003 Mercury MarauderChange (https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/)


Bulb Position (https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/#bulbPositionPanel)



Forward

Fog Light Bulb Front
Headlight High Beam and Low Beam

Exterior

License Plate Light
Turn Signal (Rear)
Turn Signal (Front)
Tail Light
Side Marker Light Bulb Front
Side Marker Light Bulb Rear
Parking Light
Center High Mount Stop Light Bulb
Back up Light
Brake Light


Interior

Map Light
Turn Signal Indicator Light
Trunk or Cargo Area Light
Courtesy Light
Engine Compartment Light
Dome Light
Glove Box Light
Check Engine Light Bulb
Automatic Transmission Indicator Light
Ash Tray Light
Instrument Panel Light
High Beam Indicator Light Bulb






Vehicle Note (https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/#vehicleNotePanel)




Compatible SYLVANIA Products (https://www.sylvania-automotive.com/apps/vlrg-us/Vlrg/#sylvaniaProductsPanel)

[fastblackmerc]

Actual bulb numbers:

Headlight – 9007 (2)
Fog Light - H1 (2)
Rear Stop Light / Turn Signal – 3157 (4)
High Mounted Stop Light – 912 (2)
Front Map Light – 168 (194) (2)
Rear Light (long overhead console) - 42mm Festoon (1)
Glove Compartment – 168 (194) (1)
License Plate – 168 (194)
Trunk Light – 2122 Festoon
Underhood Light – 906 (2)
Parking Light - 3157NA (amber) (2)
Vanity Mirror – 29, 30 or 31mm 6641 (4)
Rear Reading Light – 45mm Festoon (2)
Front Foot Well – 168 (194) (2)
Reverse - 3156 (2)

[GManMM]

Does anybody know if I wanted to upgrade to.LED bulbs fo we CANBus LEDs or regular LEDs?

[fastblackmerc]

Regular bulbs.

[B_Schlomy]

Are the fog light bulbs the same as the headlight bulbs?

[fastblackmerc]

No. Fog lights are H1.

[88LTDCV351]

what LEDs are you guys using for the cornering lights?