Just got a dyno done

[MarauderMarc]

Well I just got back from Mac Donald Motorsports in Stuart. I wanted to get a dyno done since it has been a while. I only did one pull because he said I was running too lean. I had a 14.6 average. He said ideally I should be at a 12.5 the entire run. Plugged in my 1725 SCT tuner and it doesnt let you adjust the A/F ratio. Damnit! So looks like I am going to need an Xcal2. He sells them for 500, but that includes every tune he has access to. And it comes with a Dyno tune. Not bad if you think about what all that costs normally.

Now for the #s Max Power 260.1 Max Torque 272.5

Intake temp. 84.8 f

Looks like no Moroso tonight:(

What RWHP do we have stock???????

[Smokie]

There is variation of course, but an average MM. would have about 240 RWHP and 254 RWTQ.
In regards to the A/F ratio, if you are N/A, once you are at WOT I would like to see a fairly consistent 13 across the rpm range, I think 12.6 is a bit rich.

[Blackened300a]

I had my car dynoed last Saturday and with the Fatory tune, Pullies, PHP Spacer,and a PHP Airbox I pulled 251 RWHP and 263 RWTQ. The Factory tune with my Mods was putting my A/F Mixture at 14.5- 15.0, which is too lean. He installed a SCT tune, Set my A/F mixture to 13 across the board and I pulled 285 RWHP and 308 RWTQ. Go for the Xcal and the proper tuning, You'll be Glad you did!

BTW, $500 for the Xcal2 with a dyno tune is a STEAL!!! I walked out paying $350 and I had the Xcal already

[MarauderMarc]

I had my car dynoed last Saturday and with the Fatory tune, Pullies, PHP Spacer,and a PHP Airbox I pulled 251 RWHP and 263 RWTQ. The Factory tune with my Mods was putting my A/F Mixture at 14.5- 15.0, which is too lean. He installed a SCT tune, Set my A/F mixture to 13 across the board and I pulled 285 RWHP and 308 RWTQ. Go for the Xcal and the proper tuning, You'll be Glad you did!

BTW, $500 for the Xcal2 with a dyno tune is a STEAL!!! I walked out paying $350 and I had the Xcal already

Well I know my next mod.....hey, how do you like your PHP spacer??? Did you notice ant difference?

[Blackened300a]

Well I know my next mod.....hey, how do you like your PHP spacer??? Did you notice ant difference?

When I first installed it, I didnt notice any difference at all. After Dyno tuning, its obvious that it does make some horsepower so its up to you if you want to spend $110 for a little extra power you can't feel.

But as they say... Every bit of Horsepower Helps

[BK_GrandMarquis]

Well I just got back from Mac Donald Motorsports in Stuart. I wanted to get a dyno done since it has been a while. I only did one pull because he said I was running too lean. I had a 14.6 average. He said ideally I should be at a 12.5 the entire run. Plugged in my 1725 SCT tuner and it doesnt let you adjust the A/F ratio. Damnit! So looks like I am going to need an Xcal2. He sells them for 500, but that includes every tune he has access to. And it comes with a Dyno tune. Not bad if you think about what all that costs normally.

Now for the #s Max Power 260.1 Max Torque 272.5

Intake temp. 84.8 f

Looks like no Moroso tonight:(

What RWHP do we have stock???????

So what did he end up setting the air/fuel ratio to? It looks like he did a hell of a tune to it.

You went from:
Max Power 260.1 Max Torque 272
to
302 rwhp 320 rwtq

Do you have a shot of the dyno sheet?