Hack Goby
01-08-2008, 10:29 AM
Now that Im not a Marauder owner anymore I have been poking around the Focus websites.There not a whole lot different than here and there some pretty quick cars there.I still have a lot of good friends here and will continue to post and Im hoping to meet a few over there also.TOP TEN QUARTER MILE TIMES
1. dragfocus 10.91@135.8
ZX2 bottom end, CGI block with esslinger 4 bolt mains, O-Ringed deck, JE pistons, Crower rods, a moldex billet crank. ZX3 Roush WRC Head, with square ports and a much better port angle than stock, cosworth buckets, web cams and custom springs. It has a sheet metal intake, a 3" mustang throttle body, a custom Kiwi exhaust manifold and down pipe, Barnes oil dry sump, custom fuel rail, and a Weldon fuel pump. The Turbo is a T4with a tial waste gate and blow off. This is connected to a Quaif 6 spd trans with a tilton triple carbon clutch, with Sway-Away 300m axles, 935 CV’s connected to 2 15/10.5/28 MT slicks. The rear end is a custom Strange strut and brake assembly. One piece carbon Kevlar front end with a Jerry Bickle mount kit. Custom Bickle wheelie bars. Aluminum dash and door panels with Defi gauges and a sparco seat. This car is still a unibody.
http://i44.photobucket.com/albums/f5...ustimeslip.jpg
2. MikeySSM80 11.24@127.68mph
473hp/415tq.@ wheels Dynojet 248, Silver State Motorsports
-Turbo, intercooled,Stg. 2 cams, ported ZX3 head,FR intake manifold, bigger valves,stock coil pack, stock plug wires,stock axles, low compression probe pistons, eagle rods,tial BOV,HKS GT II wastegate, HKS F-Con V pro stand alone engine management. Tilton Clutch, aluminum flywheel. 4"x10" K&N filter.
http://videos.streetfire.net/search/...AA945FC7B4.htm
3. Fernan@cfm 12.409@114.81
375hp/358tq, 2001 Focus, CFM Prototype turbo kit, CFM Zetec High Performance Short block 10.2:1 compression, CFM Stage 2 cylinder head, CFM cam gears, Comp cams stage 3, 2000 intake manifold, CFM High performance oil pump, CFM Underdrive pulleys, CFM 65MM Throttle body, SVT exhaust conversion kit with CFM SVT off road pipe, Ford racing svt header, Magnaflow exhaust zx3, 60lb injectors, mafia, boost-a-pump, CFM Custom tuning with SCT Xcal2, Snow performance water/methonal kit, MT slicks 22x8x15,
video link http://63.134.210.3/Video/12.4_run.wmv
http://focus.c-f-m.com/ProductImages/cfmrun12-4.jpg
4. CFM Focus 12.48@112.13mph
STOCK SHORTBLOCK (boosted for 35k) Vortech V-5 F-Trim Supercharger (17psi @ 7,200k) PWR Air/Water Cooler Ported Stock Head / Stock Valvetrain Thicker Head Gasket (9.0:1 appx) Adjustable Cam Gears Crower Stage 2 Camshafts Ported 2000 Intake 65mm Throttle Body Stock Returnless Fuel System Stock Fuel Pump 50lb Injectors Pectel Engine Management SVT Header w/ 2.5" Magnaflow Exhaust
http://www.c-f-m.com/c-f-m.com.wmv
5. tobyboom 12.55@112mph
Probe Ind. 8.2:1 pistons, Eagle Rods, Stock cams, Crower Valvetrain, Stock valves, mild port & polish, Ford Racing intake manifold, FC 65mm TB, STR Fuel Rail, 42lb Injectors, Pro-M Blow through MAF, Esslinger Cam Gears, Custom Turbo Manifold, Turbonetics Evolution wastegate, TurboneticsT3/TO4E 50 trim turbo, Focus-Power piping/intercooler, gReddy BOV, Clutch Masters Stg. IV clutch, Quaife LSD, M&H Slicks 23/8.5/15
PRORACER TUNED @ 20 PSI BY TOM OF FOCUS-POWER 302.25HP/278.66TQ @ 20PSI
http://img.photobucket.com/albums/v1...m/DSC00162.jpg[/color]
6. CFM focus 12.75@108.17mph
2001 Ford Focus zx3, CFM cam gears, CFM throttle body, CFM lower engine mount,CFM custom tuning with xcal 2, svtf header,CFM svtf off road pipe, magnaflow exhaust for svtf, and CFM custom air intake,CFM underdrive pulleys, denso iridium spark plugs, CFM cylinder head stage 2 milled to 10.5:1 compression, Comp cams stage 3 camshafts, Cm stage 4 clutch, cm aluminum flywheel, Quaife LSD, and NX nitrous kit 100 shot. MT slicks 22x8x15. 175hp before 100 shot.
http://focus.c-f-m.com/images/12.7%2... 05-23-07.jpg
7. Huntincooter 12.93@112.08
04 Twilight Blue ZX3 - Focus Sport Turbo Kit, 2.5" truebendz exhaust, BS delete kit, F2 lightweight flywheel, spec stage 2 clutch, ES lower mount bushings, VF driver side mount, SVT Brakes, Tein springs, SVT rear sway bar, Poly endlinks FS rear stress bar, 16" Rota Grids - 205-50 AVS ES 100's.
http://upload.imgspot.com/u/07/314/12/129015.jpg
8. tparker 13.322@103.537
2000 2.0L ZETEC Balanced and Blue printed ARP fasteners throughout Crower forged rods JE forged pistons 9:1 compression FC custom ported and polished 1-mm larger valves intake and exhaust Crower titanium springs and retainers Crower custom FI stage 4 cams FS/VF SC Stage 2 pulley and FC 5.7" ODP shortened intake tube Early 2000 intake manifold Quaife LSD ACT street strip clutch FS aluminum flywheel CF hood Oddisy light weight battery FS 4-1 header FS flex pipe FS Stealth exhaust VF driver side and passenger motor mounts MACS lower motor mount
http://i8.photobucket.com/albums/a46...vt/tparker.jpg
9. econorocketZX3 13.392@101.66mph
-one off turbo kit (T3/T04E, custom tubular manifold, 2.5" intercooler piping, Spearco core, GReddy Type-S bov, Deltagate, 2.5" down pipe, Pro-M 70mm MAF, 42lb/hr injectors, Autologic chip tuned by Tom, 9.5psi on 93 pump gas) 3" Trubendz flex pipe and catback FC 65mm TB FC pulley set Quiafe Competition Clutch stage 4 Clutchnet 11lb aluminum flywheel Denso Iridium plugs (2 steps colder) Magnacore plug wires Eibach Pro-dampers Eibach Sportlines Weld draglites (15x7's up front, 15x3.5's in rear) Mickey Thompson 22x8x15 slicks Moroso DS-2 skinnies
http://i8.photobucket.com/albums/a46/smurfsvt/131.jpg
10. BlownSkillet1 13.464@105.65 mph
276hp/260tq @ 11 psi, Eagle Rods, JE Pistons, Crower Cams, springs & retainers, APR Head Studs, 42lb/hr injectors, SCT tune by Steeda (X caliber 2), Steeda 65mm t/b, Custom header by CFT (Central Florida Turbo), Custom down pipe 2.5" (CFT), Custom exhaust 2.5", Custom intercooler piping, Spearco intercooler, Turbonetics T3 Turbo (.48), Turbonetics Raptor blow off, Tial wastegate w/open dump, Steeda poly mounts (all 3), Greddy Turbo Timer, Steeda Shifter, Fidanza Alum. Flywheel, Clutchmasters 4 puck clutch, Steeda springs, Torsen T-2 Diff (Ford Racing), STREET TIRES BF Goodrich Sport Comp
http://img152.imageshack.us/img152/2...meslip4rb8.jpg
1. dragfocus 10.91@135.8
ZX2 bottom end, CGI block with esslinger 4 bolt mains, O-Ringed deck, JE pistons, Crower rods, a moldex billet crank. ZX3 Roush WRC Head, with square ports and a much better port angle than stock, cosworth buckets, web cams and custom springs. It has a sheet metal intake, a 3" mustang throttle body, a custom Kiwi exhaust manifold and down pipe, Barnes oil dry sump, custom fuel rail, and a Weldon fuel pump. The Turbo is a T4with a tial waste gate and blow off. This is connected to a Quaif 6 spd trans with a tilton triple carbon clutch, with Sway-Away 300m axles, 935 CV’s connected to 2 15/10.5/28 MT slicks. The rear end is a custom Strange strut and brake assembly. One piece carbon Kevlar front end with a Jerry Bickle mount kit. Custom Bickle wheelie bars. Aluminum dash and door panels with Defi gauges and a sparco seat. This car is still a unibody.
http://i44.photobucket.com/albums/f5...ustimeslip.jpg
2. MikeySSM80 11.24@127.68mph
473hp/415tq.@ wheels Dynojet 248, Silver State Motorsports
-Turbo, intercooled,Stg. 2 cams, ported ZX3 head,FR intake manifold, bigger valves,stock coil pack, stock plug wires,stock axles, low compression probe pistons, eagle rods,tial BOV,HKS GT II wastegate, HKS F-Con V pro stand alone engine management. Tilton Clutch, aluminum flywheel. 4"x10" K&N filter.
http://videos.streetfire.net/search/...AA945FC7B4.htm
3. Fernan@cfm 12.409@114.81
375hp/358tq, 2001 Focus, CFM Prototype turbo kit, CFM Zetec High Performance Short block 10.2:1 compression, CFM Stage 2 cylinder head, CFM cam gears, Comp cams stage 3, 2000 intake manifold, CFM High performance oil pump, CFM Underdrive pulleys, CFM 65MM Throttle body, SVT exhaust conversion kit with CFM SVT off road pipe, Ford racing svt header, Magnaflow exhaust zx3, 60lb injectors, mafia, boost-a-pump, CFM Custom tuning with SCT Xcal2, Snow performance water/methonal kit, MT slicks 22x8x15,
video link http://63.134.210.3/Video/12.4_run.wmv
http://focus.c-f-m.com/ProductImages/cfmrun12-4.jpg
4. CFM Focus 12.48@112.13mph
STOCK SHORTBLOCK (boosted for 35k) Vortech V-5 F-Trim Supercharger (17psi @ 7,200k) PWR Air/Water Cooler Ported Stock Head / Stock Valvetrain Thicker Head Gasket (9.0:1 appx) Adjustable Cam Gears Crower Stage 2 Camshafts Ported 2000 Intake 65mm Throttle Body Stock Returnless Fuel System Stock Fuel Pump 50lb Injectors Pectel Engine Management SVT Header w/ 2.5" Magnaflow Exhaust
http://www.c-f-m.com/c-f-m.com.wmv
5. tobyboom 12.55@112mph
Probe Ind. 8.2:1 pistons, Eagle Rods, Stock cams, Crower Valvetrain, Stock valves, mild port & polish, Ford Racing intake manifold, FC 65mm TB, STR Fuel Rail, 42lb Injectors, Pro-M Blow through MAF, Esslinger Cam Gears, Custom Turbo Manifold, Turbonetics Evolution wastegate, TurboneticsT3/TO4E 50 trim turbo, Focus-Power piping/intercooler, gReddy BOV, Clutch Masters Stg. IV clutch, Quaife LSD, M&H Slicks 23/8.5/15
PRORACER TUNED @ 20 PSI BY TOM OF FOCUS-POWER 302.25HP/278.66TQ @ 20PSI
http://img.photobucket.com/albums/v1...m/DSC00162.jpg[/color]
6. CFM focus 12.75@108.17mph
2001 Ford Focus zx3, CFM cam gears, CFM throttle body, CFM lower engine mount,CFM custom tuning with xcal 2, svtf header,CFM svtf off road pipe, magnaflow exhaust for svtf, and CFM custom air intake,CFM underdrive pulleys, denso iridium spark plugs, CFM cylinder head stage 2 milled to 10.5:1 compression, Comp cams stage 3 camshafts, Cm stage 4 clutch, cm aluminum flywheel, Quaife LSD, and NX nitrous kit 100 shot. MT slicks 22x8x15. 175hp before 100 shot.
http://focus.c-f-m.com/images/12.7%2... 05-23-07.jpg
7. Huntincooter 12.93@112.08
04 Twilight Blue ZX3 - Focus Sport Turbo Kit, 2.5" truebendz exhaust, BS delete kit, F2 lightweight flywheel, spec stage 2 clutch, ES lower mount bushings, VF driver side mount, SVT Brakes, Tein springs, SVT rear sway bar, Poly endlinks FS rear stress bar, 16" Rota Grids - 205-50 AVS ES 100's.
http://upload.imgspot.com/u/07/314/12/129015.jpg
8. tparker 13.322@103.537
2000 2.0L ZETEC Balanced and Blue printed ARP fasteners throughout Crower forged rods JE forged pistons 9:1 compression FC custom ported and polished 1-mm larger valves intake and exhaust Crower titanium springs and retainers Crower custom FI stage 4 cams FS/VF SC Stage 2 pulley and FC 5.7" ODP shortened intake tube Early 2000 intake manifold Quaife LSD ACT street strip clutch FS aluminum flywheel CF hood Oddisy light weight battery FS 4-1 header FS flex pipe FS Stealth exhaust VF driver side and passenger motor mounts MACS lower motor mount
http://i8.photobucket.com/albums/a46...vt/tparker.jpg
9. econorocketZX3 13.392@101.66mph
-one off turbo kit (T3/T04E, custom tubular manifold, 2.5" intercooler piping, Spearco core, GReddy Type-S bov, Deltagate, 2.5" down pipe, Pro-M 70mm MAF, 42lb/hr injectors, Autologic chip tuned by Tom, 9.5psi on 93 pump gas) 3" Trubendz flex pipe and catback FC 65mm TB FC pulley set Quiafe Competition Clutch stage 4 Clutchnet 11lb aluminum flywheel Denso Iridium plugs (2 steps colder) Magnacore plug wires Eibach Pro-dampers Eibach Sportlines Weld draglites (15x7's up front, 15x3.5's in rear) Mickey Thompson 22x8x15 slicks Moroso DS-2 skinnies
http://i8.photobucket.com/albums/a46/smurfsvt/131.jpg
10. BlownSkillet1 13.464@105.65 mph
276hp/260tq @ 11 psi, Eagle Rods, JE Pistons, Crower Cams, springs & retainers, APR Head Studs, 42lb/hr injectors, SCT tune by Steeda (X caliber 2), Steeda 65mm t/b, Custom header by CFT (Central Florida Turbo), Custom down pipe 2.5" (CFT), Custom exhaust 2.5", Custom intercooler piping, Spearco intercooler, Turbonetics T3 Turbo (.48), Turbonetics Raptor blow off, Tial wastegate w/open dump, Steeda poly mounts (all 3), Greddy Turbo Timer, Steeda Shifter, Fidanza Alum. Flywheel, Clutchmasters 4 puck clutch, Steeda springs, Torsen T-2 Diff (Ford Racing), STREET TIRES BF Goodrich Sport Comp
http://img152.imageshack.us/img152/2...meslip4rb8.jpg