php intake spacer

[risky]

hey guys im looking for a php intake spacer 4 my marauder like the one that dennis yous 2 sell does anyone know where i could fined one or does anyone know a web site were i could buy one from

[fastblackmerc]

hey guys im looking for a php intake spacer 4 my marauder like the one that dennis yous 2 sell does anyone know where i could fined one or does anyone know a web site were i could buy one from

Try googeling "php intake"

[MrBluGruv]

I'm not too sure those aren't discontinued if DR quit carrying them. I saw some for sale on eBay a few months back for like 75 shipped, I'm still kicking myself for not picking one up.

[dohc324ci]

https://www.paulshp.com/cgi-bin/webstorecgi/webstore.cgi?page=600016&type=&frame=&cart_id=2164740_880

[ImpalaSlayer]

we use the same one as the mach1. id save your money.....

[musclemerc]

Well you get one from here http://www.karkraft.com/new_page_9.htm or you could register here and PM Roy for a spacer up to 1/2" made from real Phlemonic material http://www.mach1registry.org/forums/showthread.php?t=61184&page=3

[ImpalaSlayer]

i thought karkraft went out of business?

[sd8683]

I have one brand new in the box, you can have it for $80 shipped, I bought from Dennis a while back, I can't remember what I paid, but it was over $100...... I wanna say $115 maybe???

[imorb1994]

I have one brand new in the box, you can have it for $80 shipped, I bought from Dennis a while back, I can't remember what I paid, but it was over $100...... I wanna say $115 maybe???
When i got mine from DR it was $135

[SC Cheesehead]

we use the same one as the mach1. id save your money.....

+1, from what I've heard, little noticable performance gain.

[musclemerc]

Maybe +3hp and 10ftlb torque and an inproved throttle response for less then 100.00. Not bad! IMO

[dohc324ci]

I really doubt it would produce that much. I would only consider this mod along with a ported upper/lower intake. PHP has the whole package extrude honed upper intake and ported lower intake w/PHP spacer for $1200. They claim 18-25hp combined. I only got my PHP spacer because well it was half of what it would cost new and I had a ported lower intake done with the BBS project.

[babbage]

i thought karkraft went out of business?

They did! Try hitting the KarKraft homepage! http://www.karkraft.com/

I got mine for $75 I think - going out of business sale.

[ImpalaSlayer]

I really doubt it would produce that much. I would only consider this mod along with a ported upper/lower intake. PHP has the whole package extrude honed upper intake and ported lower intake w/PHP spacer for $1200. They claim 18-25hp combined. I only got my PHP spacer because well it was half of what it would cost new and I had a ported lower intake done with the BBS project.

your welcome :D

[imorb1994]

IMHO I believe the only thing this does is slightly increase throttle response, On a lightly modded N/A engine. Not worth it in my opinion. Mine will be coming off when ever I get around to my engine powder coating project.

[dohc324ci]

your welcome :D

Thanks Davey boy! It looks cool though!

[ddogg626]

On a N/A engine with a CAI and a reinhart tune would it be worth installing the spacer? What is really to gain ??

[ImpalaSlayer]

On a N/A engine with a CAI and a reinhart tune would it be worth installing the spacer? What is really to gain ??


put the money towards mods that would really make a difference, like 4.10s

[dohc324ci]

^^agreed.

Shops around here do them for 400/500 for 4.10s installed. Consensus is CAI, 4.10s and tune are the best bang for you buck mods. Gets harder after that...

[ImpalaSlayer]

^^agreed.

Shops around here do them for 400/500 for 4.10s installed. Consensus is CAI, 4.10s and tune are the best bang for you buck mods. Gets harder after that...


just harder on the wallet....

[SC Cheesehead]

^^agreed.

Shops around here do them for 400/500 for 4.10s installed. Consensus is CAI, 4.10s and tune are the best bang for you buck mods. Gets harder after that...

Only relatively cheap mod other than the above I'd add to the list is U/D pulleys.

[dohc324ci]

You can add UDP's & Electric Pump to the list of low hanging fruit mods but.....$ per HP is more expensive....after those me thinks....

[RF Overlord]

a spacer up to 1/2" made from real Phlemonic materialUh...Phenolic, maybe?

[LANDY]

i think 100 dollars for maybe a couple of HP and 5 foot punds of torque. why not?

[massacre]

I have one brand new in the box, you can have it for $80 shipped, I bought from Dennis a while back, I can't remember what I paid, but it was over $100...... I wanna say $115 maybe???

Hey Sean-

What would you take for yours if I came and picked it up?

-PM Sent

[RacerX]

Uh...Phenolic, maybe?
Phlegmolic, almost as good as Soylent Green! :D

[Phrog_gunner]

Uh...Phenolic, maybe?

I thought Phenolibist was the person who takes your blood??

[RacerX]

Phlebotomist!

[SC Cheesehead]

Phlebotomist!

I thought this was sombody who collected phlegm...:dunno:

[ctrlraven]

It's worth having if you have or plan on having headers or more open exhaust of some sort. Remember every little bit helps, it might not do a lot alone but combined with other mods it can help out.

[Paul T. Casey]

It's worth having if you have or plan on having headers or more open exhaust of some sort. Remember every little bit helps, it might not do a lot alone but combined with other mods it can help out.

A wise man indeed. And, for $80 shipped, what could it hurt? About the price of a full tank of fuel a year and a few months ago.

[RacerX]

A wise man indeed. And, for $80 shipped, what could it hurt? About the price of a full tank of fuel a year and a few months ago.
And soon to come! Hitting $3.00/Gal in some places... :shake:

[ImpalaSlayer]

And soon to come! Hitting $3.00/Gal in some places... :shake:

just paied 3.04 for 93....

[281MERC]

what about a granetelli coil on plug set???