Intake spacer!!!!!

[Mw 2309]

Where can you get an intake spacer for my mm thanks

[Blackmobile]

Not sure if they still offer it but they are still adverting it.

http://www.paulshp.com/mach-1.html

[na svt]

MMR has them.

[Mr. Man]

Save your money

[imorb1994]

Save your money

+1 not worth it

[guspech750]

Keep your $$$ and buy one of these.
http://img.tapatalk.com/d/12/11/04/utyde4a9.jpg

:burnout:


Sent from my iPhone 4S

DTR + 4.10's + Eaton swap = Wreeeeeeeeeeeeeeedom

[SC Cheesehead]

Save your money


+1 not worth it

+3

Snake Oil, IMO, but there are some that claim you'll see improved performance; if there is any, it ain't much.

What other mods have you done to the car?

[RF Overlord]

While I wouldn't call it snake oil, it's probably the least productive use of funds on the "cheap mods" list.

Mary won one and I installed it on Phoebe a few years ago...felt like there was a small gain in the mid-range, but it might have been a cool day. Put the money toward underdrive pulleys...those will make a bigger difference.

[rayjay]

I seem to remember that they actually work much better on a SC'd engine. I saw very little from mine. Too lazy to pull it off. Have to figure out what happened to my blower fan. Cars usually put up by now, but its permanently coming south with me on the 18th.

[babbage]

Pauls HP and others have shown a small dyno gain, thats why they sell.


MMR Intake Spacer for 99/01 Cobra and ALL Mach OneThis spacer better distributes airflow to the engine by raising the upper intake hat and increasing volume, Pick up 10-12 HP! Forced induction applications run safer and more powerfull due to better airflow distribution. Includes gasket and new Hardware.

[fastblackmerc]

I seem to remember that they actually work much better on a SC'd engine. I saw very little from mine. Too lazy to pull it off. Have to figure out what happened to my blower fan. Cars usually put up by now, but its permanently coming south with me on the 18th.

The HVAC blower?

If so, most likely the BCM. Try tapping it and it may start working for you.

[na svt]

Pauls HP and others have shown a small dyno gain, thats why they sell.


MMR Intake Spacer for 99/01 Cobra and ALL Mach OneThis spacer better distributes airflow to the engine by raising the upper intake hat and increasing volume, Pick up 10-12 HP! Forced induction applications run safer and more powerfull due to better airflow distribution. Includes gasket and new Hardware.


MMR also states you'll gain 15rw with their throttle body. Never believe their hp claims.

[breeze]

I just put kooks on and JPC is having a dyno day so when my intake spacer I'll see if I can do a before/after and test it out. U/D will be put on beforehand too.

[Vortech347]

When I had money to burn I did a before/after test with one. I picked up 5-6rwhp and about 10ft-lbs. Same dyno a week of time between. The gains were all midrange. I think up top it 5000+ RPM it was same.

[Curless]

FYI, longer intake runners = more top end...top is not what we need in these cars...

Damn it...said that wrong....

Longer intake runners = more LOWER end...

[LANDY]

FYI, longer intake runners = more top end...top is not what we need in these cars...
We need it all!

[babbage]

When I had money to burn I did a before/after test with one. I picked up 5-6rwhp and about 10ft-lbs. Same dyno a week of time between. The gains were all midrange. I think up top it 5000+ RPM it was same.

This should be a sticky.

[breeze]

Maybe I should just go ahead and put it on then to wait for dyno

[babbage]

Totally take off top cover, clean it etc, clean the lower. throw on spacer and gasket, then connect EGR to top cover then slide top cover over hold in place then drop in the top cover bolts I think is the best way to install the spacer.

[massacre]

FYI, longer intake runners = more top end.....

Pretty sure you're wrong on this ^^^.

Longer runners= low end torque production.
Shorter runners= high end HP.

[Curless]

Yep I posted that backwards... can't even blame it on auto correct!