Mod. COT

[silversnake]

Don't know if anyone cares but I too the extra COT I had to a local welder after cutting it to size. 3/4 of 1" is what I went with.http://tapatalk.imageshack.com/v2/15/03/19/ef83e7e8f02c41d9b4b620a3f981f0 68.jpghttp://tapatalk.imageshack.com/v2/15/03/19/649e6adee3a3944ca7845bb5fc8843 74.jpghttp://tapatalk.imageshack.com/v2/15/03/19/534ee32574a4f54e095862a2449862 ed.jpghttp://tapatalk.imageshack.com/v2/15/03/19/06e6ce7cafa8bbaeff0051e8bc1a5e d8.jpg. Pressured tested and ready to go. I'll clean it up and drop some fresh paint. Total cost $30


Sent from my iPhone using Tapatalk

[Zack]

Did you pressure test it?

[silversnake]

Yes sir


Sent from my iPhone using Tapatalk

[silversnake]

He says its cast steel not aluminum. I told him no but he kept insisting it was. With 30+ years of experience who am I to correct him


Sent from my iPhone using Tapatalk

[Zack]

It is steel. Garbage steel.

[silversnake]

It is steel. Garbage steel.


Your measurement was on point thanks.


Sent from my iPhone using Tapatalk

[silversnake]

http://tapatalk.imageshack.com/v2/15/03/20/83d7236e7323f4fc4d138475994e16 74.jpg. Took a 3" wire cup brush to the rust


Sent from my iPhone using Tapatalk

[silversnake]

http://tapatalk.imageshack.com/v2/15/03/20/ae3d566fe32ceba45597257d5c5bd7 bb.jpghttp://tapatalk.imageshack.com/v2/15/03/20/c4755bc39d339fd5a4cada6ae80701 4c.jpg so far so good


Sent from my iPhone using Tapatalk

[martyo]

Powder coat it!!!

[lji372]

Powder coat it!!!

why..... just rat rod the whole car :laugh:

[silversnake]

http://tapatalk.imageshack.com/v2/15/03/20/df4051af03bf8ebafaff20ec59b90c 38.jpg cheap alternative to the fancy stuff that works. Staying withing my budget


Sent from my iPhone using Tapatalk

[Zack]

Now strip the nice paint off you just sprayed and take it back to the welder. There are no hold-down tabs welded on.

[Zack]

And the 5/8" outlet tube needs to be removed and welded shut. You have my cooling mod, which goes directly to the heater core.
The pipe/hose on the PS is eliminated.

[silversnake]

Now strip the nice paint off you just sprayed and take it back to the welder. There are no hold-down tabs welded on.


It's funny after I painted it I turned around and looked into my toolbox and the first thing I saw was the mounting tabs.


Sent from my iPhone using Tapatalk

[silversnake]

And the 5/8" outlet tube needs to be removed and welded shut. You have my cooling mod, which goes directly to the heater core.

The pipe/hose on the PS is eliminated.


http://tapatalk.imageshack.com/v2/15/03/20/839f876cc599d3c14fdf8904c943b2 2a.jpghttp://tapatalk.imageshack.com/v2/15/03/20/84cbf2cca248998240062a7d8fa2d7 ac.jpg

The first pic is what I got from you. I thought I needed the T connection also. I'm slow. I thought yours were the same musclemerc's. I'll have to go back to my notes


Sent from my iPhone using Tapatalk

[Zack]

I knew this was for an eaton swap, thus the missing Tee.

[silversnake]

I knew this was for an eaton swap, thus the missing Tee.


Gotcha.. I'll make the necessary changes


Sent from my iPhone using Tapatalk

[lji372]

Whitey can get you a deal on jb weld for those tabs!

Good luck with your project. Booost B........!!!!!!!!!!!!!!!!!

[massacre]

I should start making these......

Someday lol

[lji372]

I should start making these......

Someday lol

Making what?