Great info, JB!
MM.net Village Idiot
Great info, JB!
03 Black MM: Trilogy #19, Build Date 04/02/03 #7113
03 SB MM: Lidio Tune/JLT CAI DD Build Date 04/02/03 #7114
Sick-Speed play toy
I didn't bother trying as I wanted something solid to hold up the motor mount anyways, and the fact i already had it up trying to shimmy it over. Instead of going under the car twice if needed, seemed a lot easier to just remove both at once, set something durable in there, and let it back down. I used a small 4X4 on my floor jack and a big socket. It took less than 5 minutes to put the car on ramps, remove nuts (I used a gun, but totally not needed), lift engine, set socket, and lower.Originally Posted by Motorhead350
Drivers side needed zero extra work, (without a manifold in place) but also nothing extra on my Trilogy car with blower inlet removed. The fuel rail cleared fine IIRC, if not, no biggie, to remove as well.
You guys need to remember every engine will sit differently as the motor mounts are slotted. (Hint hint for you header rubbing steering shaft guys) My engine was close to centered, this MM's engine was all the way to the right off the slots and had never been touched since new.
You will not believe the difference this makes on the passenger side! I bet money you could literally toss the cover from the front of the car and it will fall into place in less than two attempts...
Sent from my iPhone 4s using Tapatalk
Last edited by justbob; 03-13-2013 at 04:49 AM.
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Ok great. We will see what happens.
"Bye Bye, Johnny B. Goode."
Nu-NRG
take pics of your installation if you can. my Cam covers are going to be replaced soon too & I'd like to have as much know how as possible.
Sent from my handheld Zack Morris iShoe 4S.
2003 Trilogy Supercharged Marauder
Senior Member
Where's a good strong point to lift the engine at? 2 x 4 under oil pan?
It's wet outside and I'm too lazy to jack up and look under the car.
Everything Marauder, LEDs & HI
That is how I did mine.
“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
Sick-Speed play toy
Same.
Sent from my iPhone 4s using Tapatalk
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
Senior Member
"The cover will JUMP on like a small block Chevy!!!"
As long as it doesn't leak like one.I had a LOT of Chebby small blocks way back when.
Member #462
2004 DTR II
2005 H-D E Glide Classic
2009 Super Glide Custom
"Come See a Fat Old Man Sometime"
http://www.youtube.com/watch?v=IlB7bz0TrZM
There are currently 2 users browsing this thread. (0 members and 2 guests)
Posting Permissions
Reply With Quote
