Results 1 to 5 of 5

Thread: 05+ Slot Style MAF in SCT Tune

  1. #1
    Join Date
    Nov 2009
    Location
    NH
    Age
    56
    Posts
    177

    05+ Slot Style MAF in SCT Tune

    So speaking with SCT (Derive) a while back, they didn't have much of an answer for a value file for my 05+ Slot Style MAF in a gt500 112mm housing. What they did tell me was to use the BA5000/4inch value file and go from there. 112mm is close to 4.5" so multiply 4 and 4.5 by pi for your surface areas, divide for the difference, .8888 x MAF table, Fuel injector Breakpoint, Manifold Volume, Engine Displacement and Fuel Injector Slopes. This got me really close! Just a little fine tuning with a couple of widebands and this mother rips!

    Here's a wiring diagram below for the conversion.
    Or you can just by a conversion cable:
    https://www.vmpperformance.com/Plug-...p/pnp05maf.htm
    Attached Images Attached Images

  2. #2
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    I'm going to pass this info on to Jeff.

    Thanks!!

  3. #3
    Join Date
    Nov 2009
    Location
    NH
    Age
    56
    Posts
    177
    Quote Originally Posted by musclemerc View Post
    I'm going to pass this info on to Jeff.

    Thanks!!
    You're welcome!
    I also changed Injector Timing Vs ECT to 200 because of the longer duration cams. If you look at Mark Olson's cam chart, The injector point on the chart is actually where Ford has the injectors stop firing, on a hot valve for vaporization. Positive numbers are in degrees past that point and allow for firing into an open valve.

  4. #4
    Join Date
    Jul 2004
    Location
    The Dirty South
    Age
    52
    Posts
    3,836
    What lb did you end up running?

    I sent you a PM. Get back with me plz.

  5. #5
    Join Date
    Nov 2009
    Location
    NH
    Age
    56
    Posts
    177
    lololololol, I still haven't mashed it to the floor yet. I've only taken her to 15lbs. It's pullied for 20 MS109 anyone?





    On a side note.
    2005 to 2010 Slot MAFs are analog. 2011+ are GM style frequency based and can't be adapted to out PCMs.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. What's wrong with this Marauder slot car
    By kirk in forum The Classic Lounge
    Replies: 15
    Last Post: 01-12-2017, 05:54 PM
  2. For Sale Slot style MAF flange Aluminum $25 shipped!
    By MOTOWN in forum Other Parts for Sale
    Replies: 1
    Last Post: 01-27-2014, 01:22 PM
  3. paint ball. slot car track
    By slickster in forum Marauderville 11 Updates
    Replies: 3
    Last Post: 09-20-2013, 12:27 AM
  4. For Sale SCT BA5000 Slot style Maf almost new
    By DANTHEVICMAN in forum Other Parts for Sale
    Replies: 3
    Last Post: 08-25-2011, 12:44 AM
  5. Power Slot rotors and rust
    By Thomas C Potter in forum Steering, Suspension & Brakes
    Replies: 5
    Last Post: 04-24-2011, 08:08 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •