Page 2 of 2 FirstFirst 12
Results 16 to 23 of 23

Thread: Cam cover removal the easy way.

  1. #16
    Join Date
    Aug 2010
    Location
    Southern NJ - Exit 4
    Age
    62
    Posts
    3,947
    Great info, JB!

    03 Black MM: Trilogy #19, Build Date 04/02/03 #7113
    03 SB MM: Lidio Tune/JLT CAI DD Build Date 04/02/03 #7114

  2. #17
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    50
    Posts
    20,353

    Cam cover removal the easy way.

    Quote Originally Posted by Motorhead350 View Post
    Do not touch the drivers side mount correct?

    Silly question I know, but I want to be 100% clear on this. I will probably do this in two weeks.
    I didn't bother trying as I wanted something solid to hold up the motor mount anyways, and the fact i already had it up trying to shimmy it over. Instead of going under the car twice if needed, seemed a lot easier to just remove both at once, set something durable in there, and let it back down. I used a small 4X4 on my floor jack and a big socket. It took less than 5 minutes to put the car on ramps, remove nuts (I used a gun, but totally not needed), lift engine, set socket, and lower.

    Drivers side needed zero extra work, (without a manifold in place) but also nothing extra on my Trilogy car with blower inlet removed. The fuel rail cleared fine IIRC, if not, no biggie, to remove as well.

    You guys need to remember every engine will sit differently as the motor mounts are slotted. (Hint hint for you header rubbing steering shaft guys) My engine was close to centered, this MM's engine was all the way to the right off the slots and had never been touched since new.

    You will not believe the difference this makes on the passenger side! I bet money you could literally toss the cover from the front of the car and it will fall into place in less than two attempts...


    Sent from my iPhone 4s using Tapatalk
    Last edited by justbob; 03-13-2013 at 04:49 AM.
    SOLD 12/31/2021

    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.

  3. #18
    Join Date
    Apr 2003
    Location
    Rock N' Roll Hell
    Age
    38
    Posts
    15,325
    Ok great. We will see what happens.
    "Bye Bye, Johnny B. Goode."

  4. #19
    Join Date
    May 2006
    Location
    Seattle, WA
    Posts
    5,683

    Re: Cam cover removal the easy way.

    Quote Originally Posted by Motorhead350 View Post
    Ok great. We will see what happens.
    take pics of your installation if you can. my Cam covers are going to be replaced soon too & I'd like to have as much know how as possible.

    Sent from my handheld Zack Morris iShoe 4S.
    2003 Trilogy Supercharged Marauder

  5. #20
    Join Date
    Dec 2009
    Location
    Earth
    Posts
    8,032
    Where's a good strong point to lift the engine at? 2 x 4 under oil pan?

    It's wet outside and I'm too lazy to jack up and look under the car.

  6. #21
    Join Date
    Jan 2004
    Location
    Somewhere in the N.C. Triangle
    Age
    68
    Posts
    26,250
    Quote Originally Posted by tbone View Post
    Where's a good strong point to lift the engine at? 2 x 4 under oil pan?

    It's wet outside and I'm too lazy to jack up and look under the car.
    That is how I did mine.
    “When you can’t make them see the light, make them feel the heat.”
    Ronald Regan

    "The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
    is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."

    Lt. Colonel Ralph Peters

    “Be polite, be professional, but have a plan to kill everybody you meet.”
    "I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
    General James Mattis




  7. #22
    Join Date
    Mar 2008
    Location
    Next door to my neighbor
    Age
    50
    Posts
    20,353

    Cam cover removal the easy way.

    Quote Originally Posted by fastblackmerc View Post
    That is how I did mine.
    Same.


    Sent from my iPhone 4s using Tapatalk
    SOLD 12/31/2021

    Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.

  8. #23
    Join Date
    Dec 2002
    Location
    Arizona
    Posts
    2,301
    "The cover will JUMP on like a small block Chevy!!!"
    As long as it doesn't leak like one.I had a LOT of Chebby small blocks way back when.
    Member #462
    2004 DTR II
    2005 H-D E Glide Classic
    2009 Super Glide Custom

    "Come See a Fat Old Man Sometime"
    http://www.youtube.com/watch?v=IlB7bz0TrZM

Page 2 of 2 FirstFirst 12

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Valve cover removal
    By tallpaul in forum Shop Talk
    Replies: 11
    Last Post: 05-17-2012, 02:03 PM
  2. Cam bolt removal from loose cam
    By Black&Gifted in forum Shop Talk
    Replies: 15
    Last Post: 03-27-2012, 06:22 PM
  3. valve cover removal
    By ImpalaSlayer in forum Community Discussion
    Replies: 19
    Last Post: 11-29-2008, 01:48 PM
  4. 4.6L Red Cam cover
    By 03SILVERSTREAK in forum Other Parts/Misc. Wanted
    Replies: 0
    Last Post: 08-14-2008, 04:35 PM
  5. Valve cover removal
    By FastMerc in forum Buckeye Marauders
    Replies: 14
    Last Post: 05-15-2008, 05:05 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •