300B
SPC Camber bolt installation
Im finally going to drop off my car tomorrow morning to have the SPC Camber bolts installed and aligned to carfixer specs. Can someone point me in the right direction of the camber bolt instructions? It seems like I remember something about some grinding needed during install. Thanks in advance.
Really looking for a DIY with pics so I can give it to my front end shop to make sure he installs them correctly.
Last edited by JBeezy; 06-07-2017 at 02:04 PM. Reason: minor update
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
Senior Member
2003 Black - sold, back again, and sold
2003 DBP/DC - #153 Whipple 3.4 (permanent garage art)
2003 DBP/LF - # 36 (sold)
2003 DBP/LF - # 205 (sold)
2004 Black - Trilogy #43
2003 Black - shitbox (sold)
2004 DTR - shitbox #2
the grundle always gets ya
It's pretty straight forward, I did it with a dremel on one side then that died. Then used a drill and a step bit and a hand file. Would have loved a die grinder though.
300A Black
4:10 gears, Flowmaster 44's with rear cat delete, SW headers with 3 inch cats to 2.5 custom h. 3500 stall, Twisted synergy dyno tune, addco f/r , rear control arms, Novi 1200 air to air with the fixings.
Turbo Marauder
THE INSTRUCTIONS ARE IN THE INSTRUCTIONS THAT CAME WITH THE BOLTS.
Sick-Speed play toy
$5/5 minutes. Too easy!
Sent from my iPhone using Tapatalk
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
300B
Yea, I saw that when I went in my shop yesterday. Goes to show how long I've had this kit just sitting on the shelf. Why are you yelling Zack attack? LolOriginally Posted by Zack
Sent from my SAMSUNG-SM-G935A using Tapatalk
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
300B
Mine and my buddies schedule conflict and I'm over doing work like this on my back. Using a lift has spoiled me. Shop is only charging me $110 for install and alignment(carfixer specs)$5/5 minutes. Too easy!
Sent from my iPhone using Tapatalk
Sent from my SAMSUNG-SM-G935A using Tapatalk
2003 Black/Light Flint MM, PROCHARGER D1SC#30, 4.10 GEARS, REAR COOLING MOD, ZACK BIG BRAKE KIT, 3500 STALL, WIDENED REAR WHEELS.
1993 MUSTANG LX HATCH, 347 STROKER, 3.73 GEARS, TUBULAR K MEMBER, TKO 3550 TRANNY, AEROSPACE DUAL PISTON BREAKS.
Turbo Marauder
My bolt kit came with the aluminum removal bit
Everything Marauder, LEDs & HI
Was probably slightly most costly than just the bolts.
“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
Turbo Marauder
Won it at a MM.net event raffle
Four Door Ford Whore
Sorry for the thread bump but this sort of applies.
Lowered car, SPC camber bolts, Carfixer's specs should still be good, right?
'03 Marauder | '91 Country Squire | '18 Flex Ecoboost | '92 Shadow VT1100
former Panthers: '02 MGM, '04 MGM, '04 MGM v2.0, '04 MM, '07 P71 w/5-speed, '04 CVLX, '03 SAP P71, '10 P7B
CLICK HERE and have your Marauder's COA info added to the database!!! | 2003 list ||| 2004 list
Everything Marauder, LEDs & HI
Yes.
56789
“When you can’t make them see the light, make them feel the heat.”
Ronald Regan
"The only way to deal with the Islamic State - these blood thirsty, blood-drunken, terrorists -
is to kill them, keep on killing them, until you kill the last one, then you kill his pet goat."
Lt. Colonel Ralph Peters
“Be polite, be professional, but have a plan to kill everybody you meet.”
"I come in peace. I didn't bring artillery. But I'm pleading with you, with tears in my eyes, if you **** with me, I'll kill you all"
General James Mattis
Four Door Ford Whore
Thanks a hundred.
'03 Marauder | '91 Country Squire | '18 Flex Ecoboost | '92 Shadow VT1100
former Panthers: '02 MGM, '04 MGM, '04 MGM v2.0, '04 MM, '07 P71 w/5-speed, '04 CVLX, '03 SAP P71, '10 P7B
CLICK HERE and have your Marauder's COA info added to the database!!! | 2003 list ||| 2004 list
Trying to get it right...
Q: Is Zack selling these bolts? So, help me out here: do I 1) cut the flags off the stock bolts so they can be adjusted, or 2) cut the flags off the stock bolts so that they can be removed and replaced with these?
The way I read it just cutting off the flags would work. Don't care either way. I think a die grinder will work better than an sir chisel, so was going to go that route.
Thanks for any info.
Sent from my iPhone using Tapatalk
2003 black pre-decontented 300B #5886 of 7838; Born on 10/31/02
MartyO tune, 4:10's, T/A stud & girdle, MMX shaft+DS loop, Metco control arms, Quickor RSB, Addco FSB, Megs delete tips, Granatelli solid coil connectors, NGK plugs & LP 170 stat, DR rear engine cooling mod, PI 3000 TC, Level II tranny, Art Carr deep pan, Steeda pullies/billet caps, billet door locks, Ford Racing oil cap / polished coil covers, PHP CAK & Metco carbon fiber intake, DG Motorsports CF radiator cover, Fumoto oil drain valve, oil deflector, real Autometer gauges, ScanGauge II, Weatherflectors, underbody lighting kit, Zack chrome grill, OEM spoiler & door edge guards, KB dead pedal, Dynopro aluminum sills & pedals, Viper alarm w/ remote start, MM fender badges, red painted calipers, SS inserts, Silverstar Ultras, hood bumpers, 35% tints, Gorilla lug nuts, MM valve caps, Pro-Guard, DD trunk lid liner, CM UHI kit, CM Godshead rear & steering wheel badges, S-55 badge, FilterMag, MM trunk bib, ported sub-woofer.
Weißbirke Plünderer
Zack sells head cooling mod fittings when he has them.
The SPC bolts should not be needed, UNLESS you have a lowered front suspension from custom coils or coilovers or cut stock springs. Removing the alignment flags should allow enough adjustment for stock height Marauders.
2004 SB Ported Trilogy 48
Has supporting mods and stuff
Thanks to Marty O for his help in updating this car.
R.I.P.
Rex "SC Cheesehead"
There are currently 1 users browsing this thread. (0 members and 1 guests)
Posting Permissions
Reply With Quote
