I am doing an Eaton Swap. Do I need to have a MAP sensor? There is one on the Cobra Eaton blower. Is it necessary to wire this into the Marauder ECU? Is that even possible.
I do not see this on the list of items needed for the swap
Thanks
Karl
I am doing an Eaton Swap. Do I need to have a MAP sensor? There is one on the Cobra Eaton blower. Is it necessary to wire this into the Marauder ECU? Is that even possible.
I do not see this on the list of items needed for the swap
Thanks
Karl
No not needed. Just drill and tap a hole in the lower intake to accept an IAT sensor from I believe a lightning. Cut the outer wires on the MAF (greys) and run them to the new IAT location. I use the old MAP sensor hole as a boosted vacuum reference source for the boost gauge and the fuel rail sensor.
Sent from my iPhone using Tapatalk
SOLD 12/31/2021
Cobra short block / ProCharger F1-A / Cog drive upgrade / Manley valves / Brian Tooley Racing valve springs / 80# inj. / -8 fuel line / -6 return / Aeromotive 340 pumps and regulator / 2012 GT500 TR6060 six speed / twin disc clutch / Driveshaft Shop GT500 upgraded CV joint shaft / BA5000 blow thru MAF/ 4.10's / Ford Racing 31 spline set up and Girdle / Metco D.S. safety loop / Stainless Works headers, cats, and everything else out back / ClassGlass hood / Bob's hood strut mod / Hurst line lock / Metco control arms / Addco front and rear sway bars / Monroe severe duty shocks all around / Race concepts rotors / Badgeless grille / 35% tint / FBM's interior LED kit and ambient lighting kit / Pioneer FB700 deck / kenwood speaker 4 Ch. / Rockford Fosgate 10" sub and amp / Kicker 6 X 8's all around / back up cam / bluetooth / Pioneer Xm / 704 RWHP 603 RWTQ tuned by Mo's Speedshop.
The old MAP sensor has both MAP and IAT together. You can either do as suggested above, or figure out the wiring and tie the IAT portion of the MAP sensor into the MM wiring harness.
Thanks to Darrin @ BC Automotive:
$1800 and it was worse than when he started!
Brian (FordNut) FPG # 1458 of 7838
03 MM 300A (Lotsa mods, 130k mi) was 303rwhp/318rwtq N/A
then 476/410 D1SC ProCharged on stock block
then 660/555 D1SC PC on 5.3 wet sleeved Teksid alum big bore stroker
then 365/369 N/A on 5.3 wet sleeved Teksid alum big bore stroker
Now 751/617 3.4L Whipple on 5.3 Boss5.0 iron big bore stroker
03 MM 300B Silver (Mostly stock, originally wife's car, 370k mi) FPG # 7053 of 7838 or 49 of 417 SB
03 MM 300B Silver, Stock, wife's next one, 136k mi FPG # 7134 of 7838 or 89 of 417 SB
04 MM Silver, Stock, on standby 85k mi, FPG # 1212 of 3214 or 432 of 997 SB
01 F150 longbed
01 F150 shortbed
00 F150 4x4 stepside
01 F150 4x4 7700
68 Stang FB (70 351C 4V, 4 wheel discs, project car)
Mods listed here (some items not current): FordNut's Mods
You can use the cobra map/iat sensor but only utilize pins 3&4 for iat
There are currently 1 users browsing this thread. (0 members and 1 guests)