heat/ac blower problem

[ultravorx]

hey guys, the other night i noticed my blower stopped working, it didnt work in the fan control or automatic. So i started checking fuses, and one under the hood was blown. a 20 amp power distribution fuse. i replaced it and still nothing.
i proceeded to check the relay, and it was not clicking when the fan was turned on. so i tried the air suspension relay, nothing. I then went to see if proper voltage was hitting the relay pack, and it seem like it wasnt working, i decided to call it quits and put the relay back it, to my surprise it clicked and my friend said the blower kicked on!!?!
Could this have been a loose connection in the fuse junction box, or a stuck relay? i have no idea what caused this, but i dont want it to be a chroonic problem. But 3 days and so far no problems!


any info would be great!!!
Frank

[ultravorx]

well it happened again, but this time no luck playing with the relay, the relay is working, and 12v is going to the blower.


could it be a bad blower, it looks like its a 2 wire setup, so i should be a ble to pull it apart and check it out, what do you guys think?

Frank

[Rider90]

carry a screw driver around or a small rubber mallet. Next time it happens pull over and pop the hood. The housing for the blower is on the passenger side close to the firewall just above the inner fender - it's a round housing. Take the handle of the screw driver or the rubber mallet and tap the housing. This is a common problem that even I have experienced on another Panther. If the fan starts to work after tapping the housing it's time to replace the blower motor.

Good luck!

[ultravorx]

I tried the love tap method. it started to make A noise like it wanted to move, but never happened again.

I also tried the self diagnosis with the off/floor button and got no codes

if I do replave the motor myself, is it done from the motor side of the car or the interior side of the car.


thanks in advance!

[ultravorx]

I just tried giving the fan 12v and it worked, so it looks like its not the blower, but with no codes showing up, I'm at a loss!



frank

[KMABOSS302]

Frank,check the blower motor resistor plug.After popping two of them I found one of the terminals reversed,so it would not snap into the plug.It was one of the 10 or 12 ga.wires.The resistor is located on the heater box behind R/S valve cover.I hope this helps.Good luck,Kevin

[DEFYANT]

Was it resolved? If so, how?

[thePunisher]

it nneds a blower speed controller. ford basic # 19e624. it is located on the firewall behind the pass side valve cover. it is a rectangular box. just tap on it and the fan will probalby come on.

[frdwrnch]

I second the speed controller. They fail periodically. Fan always has 12V switched and controller varies the amount of ground to control speed.

[ammolance]

Well, not sure if there's more info on this or not, but my fan isn't working all of the sudden. Disclaimer: I am extremely incompetent when it comes to mechanining as I've mentioned before. I tapped the round thing that looks like it has a nipple on it above the passenger wheel fender, and nothing at all. I also tapped what I thought was the "rectangle" box behind passenger valve cover - nothing. When I cycle through the different modes (floor, floor/def, A/C, etc) I can hear the vents or whatever opening up for the associated application, but fan just isn't working. Checked fuse 15 and 16 and things looked normal. Any suggestions? '03 Marauder.

[RubberCtyRauder]

is this what you tapped on with screwdriver? see pics in thread

http://mercurymarauder.net/forums/sh...ad.php?t=48707

[RF Overlord]

I tapped the round thing that looks like it has a nipple on it above the passenger wheel fender, and nothing at all.

That's the blower motor (fan). They don't usually go bad.

I also tapped what I thought was the "rectangle" box behind passenger valve cover - nothing.

That's the BMSC {Blower Motor Speed Controller) module...that's what normally fails.

Tapping on them doesn't always work. You need to verify voltage at the blower motor to determine which is actually bad. Borrow a voltmeter from someone and unplug the blower motor connector. Turn the system on to high and you should have 12V.

Or ask a mechanically-minded friend to do this for you.

[ammolance]

is this what you tapped on with screwdriver? see pics in thread

http://mercurymarauder.net/forums/sh...ad.php?t=48707

Took a look at the pics in the thread - the one thing was against the fire wall right behind the passenger valve cover, and is kinda hard to see the whole thing. orientated up to down with regards to the rectanglish shape.

[ammolance]

That's the blower motor (fan). They don't usually go bad. That's the BMSC {Blower Motor Speed Controller) module...that's what normally fails.

Tapping on them doesn't always work. You need to verify voltage at the blower motor to determine which is actually bad. Borrow a voltmeter from someone and unplug the blower motor connector. Turn the system on to high and you should have 12V.

Or ask a mechanically-minded friend to do this for you.

Thanks for the info - I'll have to get someone over who can test the voltage as if it were bad, and i wasn't getting power, I'd think that i'm not testing it correctly. Pretty frustrating I can't fault isolate that, but I just am not confident enough to know that I'd be testing correctly.

[fastblackmerc]

I have repaired BCM'S if needed.